Ontworpen & gemaakt in Frankrijk 6K fans op Facebook · Volg ons
Beantwoord Installatie & wifi Alle modellen

Wifi-installatie: ik voer mijn netwerk en wachtwoord in, maar de Pylon-Monitor verbindt nooit

Gevraagd op · Bijgewerkt · 1 antwoord

Kort antwoord

Stel hem minstens 5 m van de router in, zorg dat hij een 2,4 GHz-netwerk kan joinen (een apart 2,4 GHz- of gastnetwerk helpt; vermijd „alleen WPA3”), controleer het wachtwoord teken voor teken en voed hem met een 5 V / 2 A-stekkerlader. Als laatste redmiddel herinstalleert u hem via USB op pylon-monitor.com/reset.

Klant A. 🇦🇺 Australië Vraag
Nederlands · vertaling

Hallo, ik heb een van uw Pylon-Monitors gekocht. Ik heb de instructies gevolgd en kom steeds op hetzelfde punt: stap 4, kies uw thuiswifi. Ik selecteer mijn wifi (die op mijn telefoon verschijnt), voer naam en wachtwoord in, het lijkt door te gaan, maar de Pylon-Monitor kan geen verbinding maken met de wifi.

Andere apparaten verbinden wel met de wifi. Ik heb zelfs de wifinaam ingekort, omdat het scherm de laatste letter afkapte. Ik heb de reset (2 klikken) vaak gedaan — ik heb het waarschijnlijk 40 of 50 keer zonder succes geprobeerd. Op een bepaald moment sprak hij op het scherm met de batterijen. De wifi is zowel 2,4 als 5 GHz. Mis ik iets?

🇬🇧 Engels

Hello, I purchased one of your Pylon-Monitors. I went through the instructions and always get to the same point: step 4, choose your home WiFi. I select my WiFi (which shows on my phone), write the name and password, it seems to go through, but the Pylon-Monitor can't connect to the WiFi.

Other devices connect to the WiFi. I even changed the WiFi name to a shorter one, as the screen cut off the last letter. I did the reset (2 clicks) a number of times — I have probably tried 40 or 50 times with no success. At some point it was talking to the batteries on the screen. The WiFi is both 2.4 and 5 GHz. Is there something I am missing?

Pylon-Monitor-teamOfficieel antwoord
Nederlands · vertaling

Bedankt voor uw uitgebreide bericht. U heeft alles goed gedaan, en het goede nieuws is dat het apparaat uw batterijen leest: de batterijkant werkt. Alleen de wifiverbinding moet worden opgelost. Dit lost het meestal op, van de eenvoudigste stap tot de meest grondige:

1. Afstand tot de router. Sommige eenheden hebben moeite met verbinden als ze heel dicht bij de router staan. Zet het apparaat voor de installatie in een andere kamer of minstens 5 meter weg en voer stap 4 opnieuw uit.

2. De 2,4 GHz-band van uw router. Het apparaat gebruikt alleen 2,4 GHz. Met een router die één naam deelt voor 2,4 en 5 GHz werkt het meestal, maar sommige routers weigeren het of sturen het weg. Als de uwe het toestaat, maak dan een apart 2,4 GHz-netwerk (een gastnetwerk is prima) en verbind het apparaat daarmee. Staat de beveiliging op „alleen WPA3”, zet die dan op „WPA2/WPA3” of „WPA2”.

3. Wachtwoord. Controleer het letter voor letter, inclusief hoofdletters: één verkeerd teken geeft precies het resultaat dat u beschrijft.

4. Voeding. Voed het apparaat met een USB-stekkerlader (5 V, 2 A) in plaats van via een computerpoort of een zwakke adapter.

5. Volledige herinstallatie via USB. Als het nog steeds niet verbindt, herinstalleer dan de nieuwste versie vanaf een computer op pylon-monitor.com/reset (Chrome of Edge, USB-datakabel). Dit wist het apparaat en begint helemaal opnieuw, wat een gewone reset niet doet. Stel daarna uw wifi opnieuw in.

🇬🇧 Engels

Thank you for your detailed message. You have done everything right, and the good news is that the device reads your batteries: the battery side works. Only the WiFi connection needs sorting out. Here is what usually solves it, from the simplest step to the most thorough:

1. Distance to the router. Some units have trouble connecting when they are very close to the router. For the setup, place the device in another room or at least 5 metres away, then run step 4 again.

2. Your router's 2.4 GHz band. The device only uses 2.4 GHz. With a router that shares one name for 2.4 and 5 GHz it usually works, but some routers refuse or steer it away. If yours allows it, create a separate 2.4 GHz network (a guest network is fine) and connect the device to that one. If the security setting is "WPA3 only", switch it to "WPA2/WPA3" or "WPA2".

3. Password. Check it letter by letter, including capitals: a single wrong character gives exactly the result you describe.

4. Power supply. Power the device from a USB wall charger (5 V, 2 A) rather than from a computer port or a weak adapter.

5. Full reinstall over USB. If it still won't connect, reinstall the latest version from a computer at pylon-monitor.com/reset (Chrome or Edge, USB data cable). This erases the device and starts from scratch, which a normal reset does not do. Then set up your WiFi again.

Was dit antwoord nuttig?
#WiFi#setup#2.4 GHz#WPA3#captive portal#troubleshooting

Gepubliceerd zonder namen of contactgegevens. Klanten worden alleen met initiaal en land vermeld.

Sluit u aan bij 6.000 Pylon-Monitor-fans op Facebook

Nieuws, firmware-updates, echte installaties en tips: volg de pagina en stel uw vragen aan de community.

Volg ons op Facebook