Il Pylon-Monitor può funzionare insieme a Solar Assistant, su uno stack di sei US5000C con revisioni BMS diverse?
Chiesta il ·Aggiornata ·1 risposta
In breve
Sì. Solar Assistant dialoga con le batterie via CAN/RS485, mentre il Pylon-Monitor usa la porta Console, separata, quindi non interferiscono. Le unità con revisioni BMS diverse vengono tutte lette correttamente. Il Pylon-Monitor non può però allineare le revisioni BMS — solo Pylontech o un distributore possono farlo.
R
Cliente R.Domanda
Italiano · traduzione
Ho uno stack di 6 Pylontech US5000C. Questo dispositivo è in grado di aggiornare il firmware delle batterie? Due delle mie unità sono leggermente più recenti e vorrei averle alla stessa revisione.
In secondo luogo, ho Solar Assistant su un Orange Pi per monitorare le batterie e i miei tre inverter Voltronic Axpert da 11 kW (trifase, off-grid ma collegati alla rete). La vostra unità può funzionare insieme a Solar Assistant? A proposito, ha un ottimo aspetto.
🇬🇧 Inglese
I have a stack of 6 Pylontech US5000C. Is this device able to update the battery firmware? Two of my units are slightly newer and I would like to have them at the same revision.
Secondly, I have Solar Assistant running on an Orange Pi to monitor the batteries and my three Voltronic Axpert 11 kW inverters (3-phase, off-grid but grid-attached). Is your unit able to run alongside Solar Assistant? Looks great, by the way.
PM
Team Pylon-MonitorRisposta ufficiale
Italiano · traduzione
Grazie per i complimenti!
Aggiornamenti del firmware delle batterie: no, ed è voluto. Il Pylon-Monitor legge soltanto dalla batteria, con gli stessi comandi di diagnostica standard dello strumento console di Pylontech (pwr, info, bat, stat), e non scrive mai nulla. Portare le vostre due unità più recenti alla stessa revisione BMS delle altre quattro può farlo solo Pylontech o il vostro distributore, con il loro strumento di servizio. La buona notizia: per il monitoraggio non serve che siano uguali. Il Pylon-Monitor si adatta a ciò che la console di ciascuna batteria riporta, quindi tutte e sei compaiono correttamente in ogni caso.
Insieme a Solar Assistant: sì. Solar Assistant dialoga con le vostre batterie tramite il collegamento CAN/RS485 (e con i vostri Axpert tramite la loro comunicazione). Il Pylon-Monitor usa la porta Console separata della batteria, un’interfaccia indipendente pensata per monitoraggio e diagnostica, quindi i due non interferiscono. Collegate il Pylon-Monitor alla porta Console della batteria master e lasciate la vostra configurazione di Solar Assistant esattamente com’è.
Una cosa da verificare: se il vostro Solar Assistant è collegato alla porta Console stessa (insolito sugli impianti Axpert/Voltronic, che normalmente usano RS485), quella porta sarebbe già occupata. In una configurazione standard è libera.
🇬🇧 Inglese
Thanks for the kind words!
Battery firmware updates: no, and it's deliberate. The Pylon-Monitor only ever reads from the battery, with the same standard diagnostic commands as Pylontech's own console tool (pwr, info, bat, stat), and never writes anything. Bringing your two newer units to the same BMS revision as the other four is something only Pylontech or your distributor can do, with their service tool. The good news: you don't need them matched for monitoring. The Pylon-Monitor adapts to whatever each battery's console reports, so all six show up correctly either way.
Alongside Solar Assistant: yes. Solar Assistant talks to your batteries over the CAN/RS485 link (and to your Axperts over their own comms). The Pylon-Monitor uses the battery's separate Console port, an independent interface meant for monitoring and diagnostics, so the two don't interfere. Plug the Pylon-Monitor into the Console port of the master battery and leave your Solar Assistant setup exactly as it is.
One thing to check: if your Solar Assistant is wired into the Console port itself (uncommon on Axpert/Voltronic installs, which normally use RS485), that port would already be taken. In a standard setup it is free.
Google Analytics 4 (tramite Tag Manager) ci aiuta a misurare il traffico di Pylon-Monitor.com, nel rispetto della vostra privacy. Nessun cookie pubblicitario. Informativa su privacy e cookie.