-
1answer
I have 15 Pylontech batteries of mixed models, and when I connect them all only the first 9 start. Can I make a single stack with a single Pylon-Monitor?
Nine batteries is 1 master + 8 slaves, the limit of older US2000 batteries without the "C": in a mixed stack, the oldest model sets the limit. Either make two groups with one Pylon-Monitor each, or keep one stack of recent models.
-
1answer
My US2500 has a different Console connector (4-pin). How do I connect the Pylon-Monitor?
Older Pylontech batteries (US2000B, US2000 Plus, US2500) have a small 4-pin RJ11/RJ10 Console socket instead of RJ45. They work with an RJ11-to-RJ45 adapter cable you can make yourself: RJ11 pin 2 → RJ45 pin 6, pin 3 → pin 3, pin 4 → pin 8.
-
1answer
We have over 10 systems with 3 to 80 batteries each. One device per system? Does it work with 80 batteries?
One Pylon-Monitor per battery group, on the Console port of the group's master: it reads up to 16 batteries. A system of 80 batteries is several groups joined by an LV-HUB, so it needs one device per group (at least 5). All systems can then be followed together on the fleet view.
-
1answer
Is the Pylon-Monitor compatible with BST batteries that look like Pylontech but have no Console port?
No. The Pylon-Monitor reads Pylontech batteries through their Console port, using Pylontech’s own console protocol. Other brands that look similar use different protocols, and without a Console port there is no way to connect it.
-
1answer
Can the Pylon-Monitor read two stacks of 7 Pylontech Force L1 batteries, cell by cell?
Yes. The Force L1 is supported and every battery and every cell is shown individually. One Pylon-Monitor on the master reads up to 16 batteries; if each stack has its own master, you need one Pylon-Monitor per stack.
-
2answers
Can one Pylon-Monitor read a US3000C master with four chained US2000C (5 batteries or more)?
Yes. One Pylon-Monitor plugged into the master's Console port reads every battery in the chain — up to 16 — and shows each one individually, with no error. Mixed models (US3000C + US2000C) are fine, and every cell of every battery is shown.
-
2answers
Is Pylon-Monitor compatible with Pylontech H48074 high-voltage modules behind an SC0500 controller?
Yes, since firmware 2.8, on generation 2 and the Lite: the device reads high-voltage packs driven by a controller such as the SC0500 through its Console port, and detects the high-voltage pack by itself. The support was built from real controller readings, but an H48074 has not yet been connected to a Pylon-Monitor.
-
1answer
Does Pylon-Monitor work with an SC0500 controller and 7 × H48050 behind it?
Yes, since firmware 2.8 (generation 2 and Lite): H48050 modules behind an SC0500 controller are read through the controller's Console port, with nothing to configure — state of charge, voltage, current, temperatures, every module and every cell, alarms and status.
-
1answer
Mixed US2000 and US3000 of different years — does it work, also on an iPad, and what else do I need?
Yes: mixed Pylontech models and ages are read individually, since the device adapts to each battery's own console output. The dashboard runs in any browser, including Safari on an iPad, with no app. You only need a USB power source — the Console cable and the USB cable are included.
-
1answer
Is the Pylontech UP5000 compatible, with 5 batteries and Home Assistant?
Yes. The UP5000 has the same low-voltage Console (RS-232) port and console protocol as the supported US5000 and UP2500. One Pylon-Monitor on the master's Console port reads all five batteries individually, and Home Assistant works through MQTT auto-discovery or a REST sensor.
Published without names or contact details. Customers are shown by initial and country only.